Keep Sand Clean and Ready for Use with Custom Sandbox Covers
MightyCovers.com offers Custom Sandbox Covers made from the most advanced and improved 18 oz. solid reinforced poured rubber vinyl. Our covers are designed to fit your swing set or fort sandbox — we can make your sandbox cover to nearly any size that you may need.
You can choose to have your cover made with post cut-outs and notches to provide your cover with a supremely snug and secure fit. Poured rubber vinyl covers come only in the colors Blue or Green.
Please note that even though the 18oz poured rubber fabric is waterproof, when there are seams and water is allowed to puddle or stand on the seams, they could leak. To prevent this, the covers may need a ball or bucket under the cover to tent up the cover and allow the water to drain off of the cover. If your cover is a long rectangle you may want to consider placing the ball on both ends so the water has nowhere to puddle.
****NOTE: PLEASE DO NOT USE OBJECTS WITH SHARP POINTS OR JAGGED EDGES THAT COULD PUNCTURE OR TEAR HOLES IN THE COVER. THIS WILL NOT BE COVERED UNDER THE MANUFACTURER’S WARRANTY.
How will you choose to fasten your cover to the sandbox? You can select stainless steel snaps or grommets that are sewn into the covers for easy removal and replacement (see photos). Or, you can choose no fasteners at all.
Screw In Snaps | Easy to install snaps. The caps of the snaps are installed in the cover and the other parts attach with a phillips head screwdriver. Grommets are also available |
Snaps are easy to install and easy to use. Made of stainless steel that resist rust and corrosion. Snaps are installed in the covers 1/2 inch from the edges | Easy to use Snaps |
***IMPORTANT NOTE*** We do not try and match existing snap placements that are on your sandbox now, however we send new snaps to screw into your sandbox with a phillips head screwdriver. |
Custom Sandbox Cover Features Click to Enlarge | ||
---|---|---|
Corner Cutouts | Snap Enclosure | Grommets |
Sandbox Cover Example – Suppose you have a 60″ x 72″ sandbox (measured outside edge to outside edge) with 4x 4 posts in each corner, and you want the cover to drop down the outside of the sandbox wall 3 by inches. The finished cover will be 66″ x 78″ with 8-1/2″ square cutouts on each corner. The 8-1/2″ cutout is enough to accommodate the 3″ drop, 1-1/2″ for the sandbox wall which is usually made of a 2 x 4 piece of wood (we will need to know the width of the frame boards) and 4″ for the post. We know that a 4″ x 4″ post is actually 3.5″ x 3.5″, but the extra 1/2″ gives you a little wiggle room.
FORM NOT REQUIRED TO BE SENT IN, IF THERE ARE NO POSTS OR OTHER CUTOUTS NO ORDER WITH POSTS OR OTHER CUTOUTS WILL BE PROCESSED WITHOUT THIS FORM COMPLETED AND RETURNED TO US, EVEN IF THE ORDER IS PLACED ONLINE. Fill out and fax completed form to 901-531-8436 or email to [email protected]. All custom sandbox covers are made to your specifications. Therefore, all sales are final. No refunds or returns can, or will, be accepted.
Please make note that these sandbox cover prices are based upon total square footage. The base price is for a cover that are 1 to 25 square feet and if it is more than 25 square feet, then an additional charge is added to the base price. You can see above when ordering with the additional square footage how much additional cost is added to the base price. |
Features:
- Heavy duty 18oz solid reinforced poured rubber
- All vinyl is made of laminated material with mildew retardant added
- Layered construction with poured rubber and a nylon mesh center
- Full UV protection
- Waterproof and weather resistant
- Available in Green and Blue
- Grommets or snaps will be positioned approximately 12-16 inches apart depending on the length of each side
K. Thompson (verified owner) –
Thanks for your quality product. Such an improvement over the wood doors we had. We have placed a child’s kickball under the cover to give it a little “lift” for the rain to drain