Custom Sandbox Covers – 11oz Mesh and 15oz Vinyl – FREE SHIPPING

Keep Your Sandbox Clean and Protected with a Custom Sandbox Cover

Screw In Snaps	Easy to install snaps. The caps of the snaps are installed in the cover and the other parts attach with a phillips head screwdriver. Grommets are also available
Snaps are easy to install and easy to use. Made of stainless steel that resist rust and corrosion. Snaps are installed in the covers 1/2 inch from the edges	Easy to use Snaps
***IMPORTANT NOTE*** We do not try and match existing snap placements that are on your sandbox now, however we send new snaps to screw into your sandbox with a phillips head screwdriver.

  Mighty Covers™ can almost make a Custom Sandbox Cover for any size or type of sandbox that you may have. It doesn’t matter if it is attached to a play set or if it is a stand alone sandbox. Only the best materials are used to make our custom sandbox covers. The most economical custom sandbox covers that we offer are made with an 11 oz. mesh fabric or a solid 15 oz. marine grade tri-laminated vinyl fabric. All hems and cutouts are reinforced with double stitching (see photo on right). You have a choice of pre-sewn in stainless steel snaps or grommets make for easy attachment. Please note that even though the 15oz vinyl fabric is waterproof, when there are seams and water is allowed to puddle or stand on the seams, they could leak. To prevent this, the covers may need a ball or bucket  under the cover to tent up the cover and allow the water to drain off of the cover. If your cover is a long rectangle you may want to consider placing the ball on both ends so the water has nowhere to puddle. ****NOTE: PLEASE DO NOT USE OBJECTS WITH SHARP POINTS OR JAGGED EDGES THAT COULD PUNCTURE OR TEAR HOLES IN THE COVER. THIS WILL NOT BE COVERED UNDER THE MANUFACTURER’S WARRANTY.  (PLEASE NOTE – If you choose snaps, we will send you the parts of the snaps that screw into the sides of your sandbox, using a Phillips head screwdriver) Or you may choose no fasteners at all. On certain situations where the sandbox is made of brick or concrete and neither snaps or grommets will work, we can make hems with Velcro pockets, which can be filled with sand or other weighted materials.

Reinforced Cutouts

Information for Measuring for a Sandbox Cover – If you have a 75″x75″ sandbox (when you measure from the outside corner to outside corner of the frame) with 4×4 posts in each corner, and you want the cover to drop down over the outside edge of the sandbox by 3 inches and fasten into the side of the sandbox. On the measuring form (Green button below marked “Print Required Quote/Order Form”) you will need to put your length and width measurements (75″x75″), the thickness of the width of the frame board (the thickness of the frame of your sandbox) for example if your frame is a 2×8 board turned up on it’s edge, then the thickness is the 2″ side, however even though lumber is called a 2×8, the actual measurements are 1-1/2″x7-1/2″, that is the measurement that must be put on the form. And the posts may be 4×4’s, but the posts are actually 3-1/2″x3-1/2″ and should be noted on the measuring form. The finished cover will be 78″x78″ with 8″ square cutouts on each corner. The 8″ cutout is enough to accommodate the 3″ drop, 1-1/2″ for the sandbox wall and 3-1/2″ for the post.  

Available 15 oz. Vinyl Colors Click to Enlarge
Green	Blue	Yellow	Red	Tan

Available 11 oz. Mesh Colors Click to Enlarge
Green Mesh	Blue Mesh

 

FORM NOT REQUIRED TO BE SENT IN, IF THERE ARE NO POSTS OR OTHER CUTOUTS NO ORDER WITH POSTS OR OTHER CUTOUTS WILL BE PROCESSED WITHOUT THIS FORM COMPLETED AND RETURNED TO US, EVEN IF THE ORDER IS PLACED ONLINE. Fill out and fax completed form to 901-531-8436. All custom sandbox covers are made to your specifications. Therefore, all sales are final. No refunds or returns can, or will, be accepted. Check out our standard size Mesh Sandbox Covers if you have a 4’x4′, 5’x5′, or 6’x6′ square sandbox with 4×4 corner posts.